— Frequently Asked Questions: AUTOSUN 2 —

Warning

“The motor must be installed by a professional in motorisation and building automation, in accordance with the SIMU instructions
and the regulations applicable in the country of use.”

INSTALLING A ROLLER SHUTTER EQUIPPED WITH AUTOSUN

Find out how easy it is to install a roller shutter equipped with an independent tubular motor, thanks to its battery and solar panel!

Click here to watch the YOUTUBE tutorial

ADD A SECOND CONTROL POINT

Add a second transmitter to your AUTOSUN 2 solar solution.
1. Press the PROG (programming) button on the individual control until the motor turns back and forth.
2. Press the PROG (programming) button on the control until the motor turns back and forth.
Your new transmitter is paired.

Click here to watch the YOUTUBE tutorial 

Add a digicode

1.Open the  Hz radio digicode with the key provided.
2. Presse the RESET button on the digicode for more than 1 second (behind the keyboard).
3. Press the individual transmitter PROG of the motor for 3 seconds => the motor turns in one direction and then in the other.
4. Type the factory code (000000) on the digicode.
5. Briefly press the digicode SET key.
6. Press the PROG button on the digicode for more than 1 second ( behind the digicode keyboard) => 1 led flashes.
7. During the flashing press one channel ( 1 of the 2 large buttons ) until the motor turns in one direction and then in the other.
8. The digicode is programmed. The code can be modified.

Click here to view the manual ref. 5050593A-Digicode SAHz

Add a general remote control

1. Press the PROG (programming) button on the individual control until the motor turns back and forth.
2. Press the PROG (programming) button on the general remote control for 1 second; the motor turns back and forth to confirm the addition.
3. Repeat the same operation on all shutters to be added.
Please note, if you already have a multi-channel remote control, remember to select the right channel before pairing.

Click here to watch the YOUTUBE tutorial 

PAIR A TRANSMITTER FOLLOWING A MALFUNCTION OR LOSS OF THE INITIAL TRANSMITTER

1. Disconnect the solar panel from the motor.
2. Disconnect the battery from the motor for 3 seconds.
3. Reconnect the battery to the motor for 8 seconds.
4. Disconnect the battery again from the motor for 3 seconds.
5. Reconnect the battery to the motor. The motor turns back and forth.
6. Press the PROG (programming) button on the new transmitter to be paired (approximately 3 seconds) until the motor turns back and forth once.
Your new remote control is paired with the motor.
7. Reconnect the solar panel again

REMOVE A CONTROL POINT

1. Press the PROG (programming) button on the individual transmitter until the motor turns back and forth.
2. Press the PROG (programming) button on the transmitter to be removed for 1 second, the motor turns back and forth to confirm the removal.
The remote control is deprogrammed.

WHICH END LIMIT SETTING MODE TO SELECT?

Discover the 4 different ways to adjust your engine from the Electronic radio engine range depending on your installation.
ALL-AUTOMATIC, SEMI-AUTOMATIC LOW, SEMI-AUTOMATIC HIGH and MANUAL Mode

Click here to watch the YOUTUBE tutorial 

PROGRAM THE MOTOR IN MANUAL MODE

1. Press the UP and DOWN buttons simultaneously until the motor turns back and forth.
2. Check the rotation direction using the UP and DOWN buttons; if the direction is reversed, press the STOP button until the motor turns back and forth.
3. Using the UP and DOWN buttons, move the shutter to the desired low position: during this operation, continue to hold down the transmitter buttons to lower or raise the shutter.
4. Once the shutter is correctly positioned, press the STOP and UP buttons simultaneously until the shutter starts to move. The shutter should rise on its own (do not hold down the button).
5. Using the STOP button, stop the shutter at the top.
6. Using the UP and DOWN buttons, adjust the desired upper position.
7. Once the shutter is correctly positioned, press the STOP and DOWN buttons simultaneously until the shutter starts to move. The shutter should lower on its own (do not hold down the button).
8. When the shutter is at mid height, press the STOP button and hold it down until the motor turns back and forth (approximately 5 seconds).
9. Press the PROG (programming) button until the motor turns back and forth. The motor is programmed.

Click here to watch the YOUTUBE tutorial

PROGRAM THE MOTOR IN FULLY AUTOMATIC MODE

FULLY AUTOMATIC mode, when the upper and lower end limits are set automatically.

Click here to watch the YOUTUBE tutorial

PROGRAM THE MOTOR IN SEMI AUTO LOW MODE

SEMI AUTO LOW mode, when only the LOWER end limit is set automatically.

Click here to watch the YOUTUBE tutorial

PROGRAM THE MOTOR IN SEMI AUTO HIGH MODE

SEMI AUTO HIGH mode, when only the UPPER end limit is set automatically.

Click here to watch the YOUTUBE tutorial

REVERSE THE ROTATION DIRECTION WHEN THE MOTOR IS ALREADY PROGRAMMED

1. Position the shutter at mid height.
2. Press the UP and DOWN buttons simultaneously until the motor turns back and forth.
3. Within maximum 2 seconds following the motion, press the STOP button until the motor turns back and forth again.
The rotation direction is reversed.

MODIFY THE END LIMITS

The end limits can only be modified if the motor has been programmed in “manual” mode.
1. Position the shutter on its current end limit.
2. Press the UP and DOWN buttons at the same time until the motor turns back and forth.
3. Position your shutter in the new position using the UP and DOWN buttons.
4. Press the STOP button until the motor turns back and forth.
The new position is saved.

SAVE OR REMOVE AN INTERMEDIATE POSITION (PI)

If you want to save or remove an intermediate position on a roller shutter equipped with the AUTOSUN 2 solar solution…

Click here to watch the YOUTUBE tutorial

CANCEL PROGRAMMING AND RETURN TO FACTORY SETTINGS (MOTOR RESET)

1. Disconnect the solar panel from the motor.
2. Disconnect the battery from the motor for 3 seconds.
3. Reconnect the battery to the motor for 8 seconds.
4. Disconnect the battery again from the motor for 3 seconds.
5. Reconnect the battery to the motor. The motor turns.
6. Press the PROG (programming) button for approximately 10 seconds until the motor turns back and forth twice within a few seconds. The motor is in factory settings and ready to be programmed.
7. Reconnect the solar panel again

Click here to watch the YOUTUBE tutorial

HOW TO CHARGE A BATTERY

1. Disconnect the battery from the motor.
2. Connect the battery to the charger reference 9020638. Minimum 3hrs.
3. Reconnect the battery to the motor.
After charging, the battery should have a voltage of around 13 volts.

PUT THE MOTOR RADIO ON STANDBY

This is only possible within maximum 10 minutes after the motor programming and with a single control point paired:
Press the 3 UP/STOP/DOWN buttons simultaneously until the motor turns back and forth for around 3 seconds.
The motor is in standby.
Click here to watch the YOUTUBE tutorial

BRING THE MOTOR RADIO OUT OF STANDBY

It is only possible to bring the radio out of standby if the panel is connected to the motor and illuminated, and can only be done with the transmitter paired during programming.
Press both the UP/DOWN buttons simultaneously until the motor turns back and forth for around 10 seconds.
The motor is reactivated.

Click here to watch the YOUTUBE tutorial